Cracked furnace heat exchanger and flue backdrafting¶

Every natural gas, liquid propane, and fuel oil central heating furnace relies on a sealed, thin-walled metal chamber called the heat exchanger to keep toxic combustion exhaust physically separated from the breathable warm air blown through your home's ductwork. Inside the heat exchanger tubes, gas burners generate flame temperatures exceeding 900 to 1,100 degrees Celsius (1,650 to 2,000 degrees Fahrenheit), producing carbon dioxide, water vapor, nitrogen oxides, and, whenever combustion is incomplete or starved of oxygen, lethal concentrations of carbon monoxide (\(CO\)) and pungent aldehydes. Meanwhile, a high-volume squirrel-cage circulating blower fan pushes household room air across the outside of those hot metal tubes and distributes it into every bedroom and living area.

Over 10 to 20 years of relentless thermal expansion and contraction cycles (heating from room temperature to 260 degrees Celsius / 500 degrees Fahrenheit and cooling back down thousands of times each winter), the aluminized or stainless steel walls of the heat exchanger fatigue, rust, and split open. Simultaneously, a blocked chimney flue, a failed draft inducer fan, or extreme negative indoor air pressure caused by powerful kitchen range hoods, clothes dryers, and bathroom exhaust fans can pull deadly flue exhaust backward down the chimney right into your basement (flue backdrafting). Understanding the visual, olfactory, and mechanical warning signs of a cracked heat exchanger or backdrafting water heater / furnace flue prevents mass household carbon monoxide poisoning and basement flame rollout fires.

Yɛ eyi mprempren¶

If your carbon monoxide alarm sounds, if you smell a sharp, eye-stinging metallic or formaldehyde odor coming from your heating vents, or if you see flames rolling out the front of your furnace cabinet, execute these six steps immediately:

1. Evacuate all people and pets to fresh outdoor air immediately if CO alarms sound or symptoms appear: If a carbon monoxide alarm is beeping (typically 4 loud chirps, a pause, and 4 chirps), or if household members feel dull frontal headaches, dizziness, nausea, or sudden flu-like lethargy while the heat is running, get everyone outside immediately.
2. Switch furnace thermostat no kɔ OFF na dum emergency furnace power switch: Sɛ obiara nni sɛnkyerɛnne biara na CO alarm no nnyigye wɔ IDLH ntɛmpɛ mu a, dan wo wall thermostat mode no kɔ OFF na dane red-plate "Emergency Furnace Shutoff" toggle switch (a ɛwɔ fononoo no nkyɛn anaasɛ ɛwɔ soro basement antweri) kosi OFF.
3. To natural gas anaa propane shutoff valve a ɛdannan nkyem anan mu biako wɔ fononoo no mu paipu no mu: Hwehwɛ dade gas tuntum a ɛyɛ den a ɛhyɛn fononoo no fã no mu na dan kɔbere valve nsa a wɔde nsa yɛ no digrii 90 (dannan mu nkyem anan mu biako)** sɛnea ɛbɛyɛ a nsa no bɛtra tẽẽ (crosswise) wɔ paipu no ho.
4. Frɛ ntɛmpɛ dispatch fi abɔnten sɛ obi wɔ sɛnkyerɛnne anaasɛ ogyaframa a ɛrehyew a: Frɛ wo mpɔtam hɔ nɔma ahorow a egye ntɛmpɛ (911 wɔ United States ne Canada, 112 wɔ Europa Aman Nkabom no nyinaa mu, 999 wɔ United Kingdom) fi ɔdan no akyi. Odumgyafo kura mframa mita a wɔde anyinam ahoɔden yɛ ne mfoninitwa mfiri a wɔde yɛ mframa a ɛyɛ hyew a wɔde di dwuma wɔ ɔpepem biara mu de hwehwɛ baabi a mframa bɔne a ɛretu na wɔde oxygen a ɛsen kɛse ma.
5. Mma w’ankasa nsan nsiesie manual Flame Rollout Switch a asɛe da: Sɛ wo fononoo no gyae hyew esiane sɛ manual-reset Flame Rollout Safety Switch bi abɔ wɔ burner adaka no atifi nti a, nmia button ketewaa a ɛwɔ switch no so no na nsan mfi fononoo no ase. Rollout switch no twitwa bere a ogyaframa a ne kɛse yɛ digrii Celsius 900 reto akyi afi ɔhyew sesa nsukorade no mu esiane mpaapaemu kɛse anaasɛ afiri a wɔde gya hyew afiri a asiw nti nkutoo.
6. Ntu fononoo no bio kosi sɛ HVAC mfiridwumayɛfo a ɔwɔ tumi krataa bɛyɛ ɔhyew nhwehwɛmu: Mfa fononoo a "red-tagged" anaasɛ wususuw sɛ ɛyɛ adwuma da "anadwo biako pɛ na ama ayɛ hyew." Fa anyinam ahoɔden ahunmu ɔhyew afiri a wɔakyerɛw din wɔ UL mu a wɔde ahyɛ ɔfasu mu nhama mu tẽẽ bere a woretwɛn sɛ wɔbɛsesa ɔhyew sesa afiri no di dwuma.

--- .

Tactical gyinaesi dua ma fononoo ɔhyew exchanger mpaapaemu ne flue backdrafting¶

Fa saa adwumayɛ gyinaesi dua yi susuw fononoo ogyaframa anomalies, mframa hua, rollout akwantu, ne chimney backdrafting.

flowchart TD
    Start["Furnace Anomaly: CO Alarm, Vent Hua a Ɛyɛ nwonwa, Ogya Kɔkɔɔ, Anaasɛ Ɔhyew Biara Nni Hɔ"] --> AlarmCheck{"1. So CO alarm rebɔ ANAA obi ti yɛ no yaw, ne ho yɛ no yaw, anaasɛ ne ti yɛ no yaw?"}

    AlarmCheck -->|"Yiw: CO a wɔde di dwuma denneennen"| EvacOut["Tu Nnipa & Ayɛmma Nyinaa Fi Abɔnten Ntɛm ara; Gyae Apon no Bue bere a Worefi adi no"]
    EvacOut --> Call911["Frɛ 911 / 112 / 999 ne Gas Utility Emergency Line fi Abɔnten so"]

    AlarmCheck -->|"Dabi: Honam fam anaa mfiri mu sɛnkyerɛnne a ɛwɔ fononoo so"| SymptomType{"2. Kɔkɔbɔ sɛnkyerɛnne bɛn na wuhui wɔ fononoo anaa mframa a wɔde fa mu no so?"}

    SymptomType -->|"Ogyaframa a ɛrehyerɛn/wosow bere a main blower fan kick on"| CrackSign["Classic Sign of a Cracked Heat Exchanger (Afiri a Wɔde Bɔ Mframa a Ɛma Mframa Nhyɛso) ."]
    SymptomType -->|"Yellow/orange lazy burner ogyaframa + tuntum soot streaks"| IncompleteComb["Ɔhyew a Enwie: Ɔhyew a Ɛto so Abien a Wɔde Sesa Nneɛma a Wɔde Plugged anaasɛ Flue a Wɔasiw"]
    SymptomType -->|"Manual Flame Rollout Switch ahwe ase ANAA ahyew anim pon"| Rollout["CRITICAL FIRE & CO HAZARD: Ogya a Ɛretow Fi Ɔhyew Adaka no Anim"]
    SymptomType -->|"Mframa a ɛyɛ hyew a ɛrehwie agu draft hood anaa plastic rings a ayɛ hyew wɔ nsu a wɔde yɛ ɔhyew so"| Backdraft["Chimney Flue Backdrafting a ɛkɔ Basement / Utility Room mu"]

    CrackSign --> ShutDown["Dane Thermostat OFF + Flip Red Furnace Tumi Switch OFF + Dane Gas Valve 90° OFF"]
    IncompleteComb --> ShutDown
    Rollout --> ShutDown
    Backdraft --> ShutOffExhaust["Dum Exhaust Fans/Dryer; Bue Mfɛnsere 5 cm (2 in); Tow Afiri no Gas Valve no mu"]

    ShutDown --> CallHVAC["MMFA Furnace no Nsan Mfi Ase; Frɛ HVAC Mfiridwumayɛfo a ɔwɔ Tumi krataa ma Combustion & Camera Test"]
    ShutOffExhaust --> CallHVAC

--- .

Kɔkɔbɔ nsɛnkyerɛnne a wotumi hu ne honam fam a ɛkyerɛ sɛ ɔhyew a wɔde sesa nneɛma a apaapae¶

Wobɛyɛ dɛn ahu sɛ dade clamshell anaa tubular heat exchanger a ahintaw a ɛwɔ wo fononoo mu no mu apaapae ansa na carbon monoxide alarm abɔ? Hwɛ na tie saa honam fam nsɛnkyerɛnne anum yi:

1. Burner ogyaframa saw mpofirim, wosow, anaasɛ ɛbɔ bere a blower fan titiriw no dan no¶

Sɛ wo thermostat hwehwɛ sɛ ɔhyew ba a, fononoo bi di kan sɔ ne gas hyew ahorow no na ɛtwɛn sikɔne 30 kosi 60 ma dade ɔhyew sesa no ayɛ hyew ansa na asɔ indoor circulating blower fan kɛse a ɛwɔ kabinet no ase no.

• Healthy intact heat exchanger: Bere a burners no nkutoo na ɛretu mmirika no, ogyaframa no yɛ pintinn, crisp blue cones a ɛrebobom brɛoo kɔ heat exchanger tubes no mu. Sɛ dan mu blower fan kɛse no bɔ wɔ sikani 45 akyi a, burner ogyaframa no nhinhim anaasɛ ɛnsakra ne nsusuwii koraa, efisɛ blower mframa no ayɛ nea wɔatoto mu koraa wɔ dade nhama no akyi.
• Ɔhyew sesafo a apaapae anaasɛ apaapae: Nea ɛto so abien pɛpɛɛpɛ a dan mu mframa a ɛbɔ fan kɛse a ɛkyinkyini no bɔ (a mframa whoosh a ano yɛ den ka ho), ofie mframa a nhyɛso kɛse fi mframa a ɛbɔ no mu no hyɛ ne kwan fa mpaapaemu no mu kɔ ɔhyew afiri no mu, anaasɛ ɛtwe mframa a ɛhyew no fi mu. Sɛ wohwɛ ahwehwɛ kurukuruwa ketewa a wɔde hwɛ ade a ɛwɔ fononoo pon no so no mu a, wubehu sɛ ogyaframa bruu a ɛyɛ hyew no wosow mpofirim ara, ɛwosow ɔfã biara, ɛdannan kɔkɔɔ-akuturuku wɔ n’afã horow, anaasɛ ɛpia kɔ akyi kɔ fononoo no anim bere a blower motor no bɛhyɛ mu no.

2. Ogyaframa kɔkɔɔ anaa borɔdɔma a ɛyɛ ɔkwasea sen sɛ ɛbɛyɛ bruu a ɛyɛ crisp jets¶

Abɔde mu mframa anaa propane wim mframa anaasɛ induced-draft burner a wɔayɛ no yiye no hyew denam ogyaframa bruu a ɛyɛ den, ɛyɛ crisp, a ɛrebobom (ɛtɔ mmere bi a ɛwɔ mu cones nketenkete a ɛyɛ bruu a ɛyɛ mmerɛw).

• Exception: Sɛ wode ultrasonic cool-mist humidifier reyɛ adwuma wɔ fie hɔ denam tap nsu a ɛyɛ den so a, calcium ne sodium minerals a wɔapete wɔ dan mu mframa mu no bɛdan gas stove ne fononoo ogyaframa a ɛyɛ hyew, crisp neon orange (a harmless sodium/calcium spectral emission).
• Dangerous yellow flame: If the furnace burner flames look lazy, wavy, candle-like, and bright yellow, the flame is starved of primary oxygen or impinging against a rusted, soot-choked heat exchanger wall. A yellow natural gas flame generates up to 1,000 to 4,000 parts per million (ppm) of carbon monoxide alongside heavy black carbon soot.

3. Black carbon soot streaks ("eyebrows") above the burner ports or flue¶

Inspect the sheet metal directly above the burner manifold and around the draft hood or flue pipe collar:

• Clean natural gas combustion leaves zero black soot.
• If you see feathery black carbon soot streaks (called "soot eyebrows") above the burner tubes, rust flakes mixed with black powder on the floor of the burner compartment, or white/greenish crusty tracks leaking down from the secondary condensing heat exchanger box, shut the furnace off immediately. Soot buildup rapidly plugs the narrow passages of modern fin-and-tube secondary heat exchangers, causing lethal flame rollout within days.

4. Tripped manual-reset "Flame Rollout Switch"¶

Every modern gas furnace has one or two small, button-sized thermal disc switches mounted on the metal bracket directly above the gas burners, wired in series with the 24-volt gas valve circuit. These are manual-reset Flame Rollout Switches (typically rated to trip open at 120 to 175 degrees Celsius / 250 to 350 degrees Fahrenheit).

• Why a rollout switch trips: Under normal operation, the negative suction of the draft inducer fan (or chimney updraft) pulls 100 percent of the 1,000-degree-Celsius flames forward into the heat exchanger tubes. If a heat exchanger tube is plugged with soot/rust, if the steel clamshell has split wide open and blower air is pushing back against the flame, or if the chimney flue is blocked by a bird's nest or collapsed clay tile liner, the flames have nowhere to go. They roll backward out the front of the burner box, scorching the wiring harness and tripping the rollout switch to shut off the gas valve.
• Why resetting it can burn down your house: Homeowners who watch DIY videos often take off the furnace door, find the tiny pop-out button between the two wires on the rollout switch, push it back in until it clicks, and walk away. Because the underlying blockage or cracked heat exchanger is still there, the furnace will continue rolling flames out into the cabinet until the wiring catches fire or the house fills with carbon monoxide.

--- .

Diagnostic comparison: healthy furnace vs. cracked heat exchanger vs. flue backdraft¶

--- .

Chimney flue backdrafting and the "Depressurized House" syndrome¶

Even if your furnace heat exchanger is 100 percent intact without a single crack, your family can still be poisoned by carbon monoxide if your chimney or vent pipe backdrafts (flows backward down the chimney into the house instead of rising up to the roof).

1. Which appliances are most vulnerable to backdrafting?¶

Heating and hot water appliances are divided into two venting categories:

1. Atmospheric natural-draft appliances (Highest Backdraft Risk): Older 80-percent-efficient furnaces, standard gas boilers, and millions of common natural gas tank water heaters have no motorized exhaust fan. Instead, they rely entirely on the natural buoyancy of warm exhaust gas rising up a metal B-vent pipe or masonry chimney (natural stack effect), decoupled at the top of the tank by an open cone called a draft hood (draft diverter). Because natural buoyancy exerts a tiny upward pressure of only 2 to 5 Pascals (0.01 to 0.02 inches of water column), any negative pressure inside the house easily overwhelms the chimney and sucks outdoor air down the flue.
2. High-efficiency (90%+ AFUE) condensing sealed-combustion furnaces (Lowest Backdraft Risk): Modern high-efficiency furnaces use two sealed white PVC plastic pipes (one drawing combustion air directly from outdoors, and one using a motorized blower to push cooled 45-degree-Celsius / 115-degree-Fahrenheit exhaust outdoors through the sidewall). However, they face a different winter emergency: snow drifts, ice dams, or hoarfrost plugging the exterior PVC intake/exhaust goosenecks outside your house foundation.

2. How exhaust fans and fireplaces cause lethal backdrafting¶

In a tightly weather-stripped modern or remodeled home, running exhaust appliances pumps hundreds of cubic feet of indoor air per minute (CFM) outdoors:

• A clothes dryer exhausts 150 to 200 CFM.
• Two bathroom exhaust fans exhaust 100 to 200 CFM.
• A gourmet kitchen range hood exhausts 300 to 1,200 CFM.
• A wood-burning fireplace or wood stove roaring in the living room pulls 200 to 500 CFM up its chimney.

If all windows and doors are tightly shut in winter and no makeup air vent exists, these appliances create a negative indoor air pressure (vacuum) of -5 to -25 Pascals inside the house. To replace that exhausted air, your house sucks outdoor air down the path of least resistance: straight down your furnace and water heater chimney flue. When the gas water heater or furnace fires up against that cold downdraft, 100 percent of its carbon monoxide exhaust spills out from under the draft hood into your basement or utility closet.

MECHANICS OF CHIMNEY BACKDRAFTING IN A DEPRESSURIZED HOUSE:
   [Roof Chimney Cap]
          ||   <-- Cold outdoor air sucked DOWN chimney (-15 Pascals vacuum)
          ||
          \/
   +--------------+
   | /==========\ | <-- Open Draft Hood on Gas Water Heater / Atmospheric Furnace
   |  (CO Spills) |     Hot combustion exhaust cannot rise against downdraft;
   |  +--------+  |     spills out into basement / utility room
   |  | Tank / |  |
   |  | Burner |  |=========================> [Clothes Dryer + Range Hood + Fireplace]
   +--------------+                            Pumping 600 CFM of air OUT of tight house

3. How to spot backdrafting on your gas water heater in 5 seconds¶

Walk to your gas water heater right now and look at the cold-water and hot-water pipes on the very top of the tank next to the sheet-metal cone (the draft hood):

1. Melted plastic grommet rings: Almost all residential water heaters have colored plastic trim rings (blue around the cold inlet pipe, red around the hot outlet pipe) sitting on the top lid of the tank. If those plastic rings are melted, warped, curled up, or browned, or if the green/black insulation foam inside the pipe holes is charred, your water heater has been backdrafting 200-degree-Celsius (400-degree-Fahrenheit) exhaust gases directly into your home.
2. Soot or powdery white corrosion on the top lid: A light coating of black soot or flaky white/grey acidic condensation scale across the top metal jacket around the draft hood confirms chronic exhaust spillage.
3. What causes physical chimney blockages:
4. Collapsed terracotta clay flue tiles: When a modern furnace is vented into an old unlined brick chimney (or an oversized masonry chimney after an old oil boiler is removed), acidic water vapor condenses inside the cold brick chimney in winter, freezing and thawing until the mortar and clay tiles crumble and pile up at the base of the chimney, blocking the furnace breech connection ("orphaned water heater" or crumbling liner effect).
5. Animal nests, leaves, or snow/ice caps: Squirrels, raccoons, chimney swifts, and wasps build dense nests inside uncapped chimney flues during summer; when you turn the furnace on in October, the flue is 90 percent plugged.

--- .

High-efficiency (90%+) condensing furnaces: plugged secondary heat exchangers and frozen PVC vents¶

If your furnace vents through white PVC or black ABS/polypropylene plastic pipes out the side of your house instead of a metal chimney, it has two heat exchangers: a primary tubular steel heat exchanger, and a secondary condensing heat exchanger (which looks like a car radiator made of tightly spaced stainless-steel or polypropylene-coated aluminum fins) that extracts latent heat by condensing acidic water vapor out of the exhaust.

1. Delamination and plugging of polypropylene-lined secondary heat exchangers: Several millions of condensing furnaces manufactured in the 1990s and 2000s experienced premature corrosion where an internal plastic coating peeled off and plugged the narrow exhaust channels, causing the burners to starve for oxygen and generate thousands of parts per million of carbon monoxide alongside a strong, foul aldehyde smell.
2. Blocked condensate trap or frozen exterior PVC pipes: A condensing furnace produces 20 to 40 liters (5 to 10 gallons) of slightly acidic liquid water every day, which drains out through a clear vinyl tube. If the condensate trap clogs with slime, or if a winter blizzard buries the exterior PVC intake/exhaust pipes in a snowdrift (or grows a solid icicle over the pipe mouth), the furnace's pneumatic pressure switch will shut the burners down. During heavy snowstorms, regularly clear snow and ice at least 30 centimeters (12 inches) below your exterior plastic furnace vents while keeping your hands and face out of the exhaust plume.

--- .

Professional HVAC combustion testing and carbon monoxide alarm placement¶

A homeowner or home inspector can never confirm a heat exchanger is safe by visual inspection with a flashlight alone, because 80 percent of the heat exchanger surface is hidden behind sheet-metal baffles and blower housings.

1. What a licensed HVAC technician must measure¶

When you call a certified heating technician (such as NATE-certified in the US, TSSA-certified in Canada, or Gas Safe Registered in the UK) to inspect a suspect furnace, make sure they perform three objective tests:

1. Digital Flue Gas Combustion Analysis: Inserting a calibrated electrochemical flue gas analyzer probe into the exhaust test port before and after the main blower fan turns on. In a healthy natural gas furnace, undiluted (air-free) carbon monoxide in the flue must be under 50 to 100 ppm (usually 10 to 35 ppm), and ambient CO in the supply air ducts must be strictly 0 ppm. If oxygen (\(O_2\)) in the flue jumps upward or \(CO\) spikes when the indoor blower turns on, the heat exchanger is breached.
2. Borescope / Endoscope Camera Inspection: Threading a high-definition fiber-optic video camera through the high-limit switch hole or burner ports to visually inspect the stress-riserdimples, eyelet welds, and first bends of every heat exchanger cell.
3. Worst-Case Depressurization Draft Test (CAZ Testing): Turning on all household exhaust fans, the clothes dryer, and the range hood with interior doors closed, then measuring chimney draft pressure in Pascals with a digital manometer to verify the water heater and furnace still establish positive upward draft within 60 seconds.

2. Installing a low-level digital carbon monoxide monitor¶

Standard UL 2034 / EN 50291 residential carbon monoxide alarms are intentionally engineered to prevent nuisance trips: they will not sound an alarm below 30 ppm for 30 days, and at 70 ppm they wait 60 to 240 minutes before beeping. To catch a slow heat exchanger leak early, and to protect pregnant women, infants, older adults, and heart patients, install at least one low-level digital display carbon monoxide monitor (which displays real-time digital readings starting at 5 to 10 ppm and sounds an alert at 15 to 25 ppm) on every sleeping level of your home, placed at breathing height 1.5 meters (5 feet) off the floor.

3. Why plugged return air filters cause heat exchangers to crack in the first place¶

The single most common mechanical cause of a cracked residential furnace heat exchanger is chronic airflow restriction from a dirty air filter or blocked return vents:

1. Thermal stress cycling above 260 degrees Celsius (500 degrees Fahrenheit): Your furnace heat exchanger depends on a continuous, high-volume stream of cool indoor return air (typically 1,000 to 1,600 cubic feet per minute) flowing over the steel tubes to carry away the intense heat of the gas burners.
2. Short-cycling on the High-Limit Switch: When a homeowner forgets to change the disposable furnace filter for 6 months, or installs an overly restrictive ultra-high-MERV pleated filter and closes bedroom supply registers, airflow drops by 40 percent. The steel heat exchanger overheats past 95 degrees Celsius (200 degrees Fahrenheit) air temperature, causing the automatic High-Limit Safety Switch to shut the gas burners off while the blower keeps running to cool the metal down. Three minutes later, the burners fire back up, overheat the metal again, and shut off again ("short-cycling on limit"). Thousands of these violent thermal expansion-contraction shocks fatiguing the steel welds eventually rip a crack straight through the heat exchanger wall. Always replace standard 25-millimeter (1-inch) furnace filters every 30 to 90 days during heating season and keep at least 80 percent of your house's floor and wall vents wide open.

Taking a hands-on first aid and CPR course from the Red Cross, St John Ambulance, or a local accredited provider ensures you can recognize acute carbon monoxide poisoning and provide life-saving support while awaiting paramedics.

--- .

Nsɛm a wɔtaa bisa¶

--- .

Sources a wɔhwɛɛ mu¶

• United States Consumer Product Safety Commission (CPSC, United States): Carbon Monoxide Poisoning from Residential Heating Systems, Cracked Heat Exchangers, and Flue Gas Spillage Investigations.
• National Fire Protection Association (NFPA, United States) and American Gas Association (AGA): NFPA 54 / ANSI Z223.1 National Fuel Gas Code (Category I to IV Venting, Draft Hood Spillage, and Combustion Air Requirements).
• Health and Safety Executive (HSE, United Kingdom) and Gas Safe Register (United Kingdom): Unsafe Situations Procedure (GIUSP) for Flueless and Open-Flued Gas Appliances, Spillage Testing, and Heat Exchanger Integrity.
• Technical Standards and Safety Authority (TSSA, Canada) and CSA Group (Canada): CSA B149.1 Natural Gas and Propane Installation Code and Carbon Monoxide Safety Bulletins on Delaminating Secondary Heat Exchangers.
• Building Performance Institute (BPI, United States): Combustion Appliance Zone (CAZ) Worst-Case Depressurization Testing and Flue Gas CO Action Thresholds.

--- .

Akwankyerɛ ahorow a ɛfa ho¶

• Carbon monoxide awuduru ne mframa a ɛtwetwe
• Carbon monoxide ne wusiw a wɔhome mu mmoa a edi kan
• No heat in winter: safe emergency heating
• Gas leak detection and emergency shutoff
• Chimney fire and creosote hazards
• Emergency nɔma ahorow ho kyerɛwtohɔ